Ethernet Cables

Request a QUOTE

Online Store

Cable Manufacturing
Custom Cables
Wire Harnesses
Molded Cables
Medical Cables
Tyco / AMP
Computer Cables
HDMI Cables
Network Cables
Fiber Optic Cables
Coax Cables
SCSI Cables
USB 2.0,  Adapters...
Firewire Products
Contact Us
Quote Request

Ethernet Cables
Comparison between CAT5, CAT5e, CAT6, CAT7 Cables

In the context of the 100-ohm UTP (Unshielded Twisted Pair) type of cable used for Ethernet wiring the only categories of interest are Cat3, Cat4, Cat5, Cat5e, Cat6, and Cat7. CATx is an abbreviation for the category number that defines the performance of building telecommunications cabling as outlined by the Electronic Industries Association (EIA) standards. Some specifications for these categories are shown further down.

Up until the late 1980s thick or thin coaxial cable was typically used for 10-Mbps Ethernet networks, but around that time, UTP cabling became more commonly used because it was easier to install and less expensive. UTP CAT3 and CAT4 were used for a quite limited time since the emergence of 100Base-TX networks meant a quick shift to CAT5. By the year 2000, moves to gigabit (1000Base-TX) Ethernet LANs created a need for another specification, CAT5e. CAT5e is now being superseded by CAT6 cable and there is a developing standard for CAT7.

Specifications for Cat3, Cat4, Cat5, Cat5e, Cat6, and Cat7 Cables



Spectral B/W


LAN Applications




16 MHz


10Base-T, 4Mbps

Now mainly for telephone cables



20 MHz



Rarely seen






Common for current LANs






Common for current LANs











It might seem that CAT5 and CAT5e are the same. Pretty much they are, the CAT5e specification simply included some additional limits over the CAT5 specification. The reality is that most CAT5 cable is in fact CAT5e cable just not certified as such. Here is a comparison of those extra specifications.

CAT5, CAT5e, and CAT6 UTP Solid Cable Specifications Comparison


Category 5

Category 5e

Category 6


100 MHz

100 MHz

250 MHz

Attenuation (Min. at 100 MHz)

22 dB

22 dB

19.8 dB

Characteristic Impedance

100 ohms 15%

100 ohms 15%

100 ohms 15%

NEXT (Min. at 100 MHz)

32.3 dB

35.3 dB

44.3 dB

PS-NEXT (Min. at 100 MHz)

no specification

32.3 dB

42.3 dB

ELFEXT (Min. at 100 MHz)

no specification

23.8 dB

27.8 dB

PS-ELFEXT (Min. at 100 MHz)

no specification

20.8 dB

24.8 dB

Return Loss (Min. at 100 MHz)

16.0 dB

20.1 dB

20.1 dB

Delay Skew (Max. per 100 m)

no specification

45 ns

45 ns

If you're cabling a mission critical system or you want your network to be future proof, go for the CAT6 cables (and patch panels and connectors), but for the average home or small office network CAT5 or CAT5e will be just fine.

Crossover Cables vs Straight Through Cables

Ethernet patch cables can be wired in three different ways, the two main ways are called straight through and crossover. The third type is called rolled and has only specialized applications.

Generally speaking, straight through cables are used to patch between different types of equipment; for example, PCs to a hub.
crossover cables are generally used to patch between similar types of equipment; a PC to another PC for example.
Some modern hubs don't care if you use crossover cables or straight through cables, they work out what you're using and configure themselves accordingly.

As stated at the outset, the actual difference is in the wiring. Inside the UTP patch cable there are 8 physical wires although the network only uses 4 of them (the other 4 are simply wasted). The 8 wires are arranged in what's known as pairs and one pair is used to send information whilst the other pair is used to receive information.

On a PC, the pair on pins 1 and 2 of the connector send information, whilst the pair on pins 3 and 6 receive the information. To make PCs talk to each we therefore need to connect the send pair of one PC to the receive pair of the other PC (and vice-a-versa). That means we need a crossover cable. If we used a straight through cable the both be listening on the one pair - and hearing nothing, and sending on the one pair - achieving nothing.

Electrically, the straight through and crossover cables look like the diagram below: The most common cable is the straight through cable. In a home or small office network you might only have one crossover cable used - perhaps from the cable or DSL modem to the distribution hub. How do you tell what sort of cable you have in your hand? You can tell by looking at the connectors, identifying the wiring from its colors, and comparing the ends. See the next question on color codes.

Color Codes

The standards say that Ethernet connectors should be cabled with specific colors on specific pins. There are two standard layouts - if a cable has the same layout on both ends it's a straight through cable. If a cable has one layout on one end and the other layout on the other end then it's a crossover cable. Whilst not universal, the color codes shown below are generally used on professional cables.

If a cable has 568A color wiring on both ends then it's a straight through cable.

If a cable has 568B color wiring on both ends then it's also a straight through cable.

If a cable has 568A color wiring on one end and 568B color coded wiring on the other end, then it's a crossover cable.

In fact, while the colors are standardized and usually followed, that's not the important part. What's more important is that one "pair" (wires that are twisted together inside the cable sheath) is used for the transmit side and another pair for the receive side. If pairs aren't used then it's likely your cable will not work. Pairs are identified by the colors. The orange wire and the orange with white stripe (or sometimes white with orange stripe) wire are a pair. The brown wire and the brown with white stripe wire are a pair. Etc.

Network Cables vs Patch Cables

A short lead with connectors on either end which is flexible and is used to plug one piece of equipment directly into another is generally referred to as a patch cable . To make them flexible, patch leads are generally made with stranded wire.
Cables with solid core wires are more often used in permanent wiring and terminate on wall sockets and may be sometimes referred to as
network cables . These cables aren't so flexible (and will break is repeatedly flexed).

Solid Core Cables vs Stranded Cables

Solid conductor uses 1 solid wire per conductor, so in a 4 pair (8 conductor) roll, there would be a total of 8 solid wires. Stranded conductor uses multiple wires wrapped around each other in each conductor, so in a 4 pair (8 conductor) 7 strand roll, there would be a total of 56 wires.


| Cat5, Cat5E, Cat6, Cat7 Comparison | Premise Wiring | Network Cables |
Fiber Optic Cable Assemblies | Mode Conditioning Fiber |
Web Counter

| Cable Manufacturer offering Full Services | Custom Cable Services | Custom Coaxial Cables |
Wire Harness Manufacturer | Molded Cable Assemblies | AMP Cables | Computer Cable Manufacturer |
HDMI Cables | Splitters | Network Cables | Fiber Optic Cables | Coax Cable Assemblies | SCSI |
USB Adapters & Converters | Firewire | KVM | Medical Cables | Quote Requests | Home |

Copyright 2003-2014, all rights reserved.
Web Counter